<?xml version="1.0" encoding="utf-8"?><Resource>
	<label commandName="NON_SM_ENTITIES_FOUND" devLabel="Failed to identify sheet metal faces for some edges. Ensure the body is a valid sheet metal body that keeps opposite faces separate." translation="无法识别某些边的钣金平板。请确保实体是保持相对面分离的有效钣金实体。"/>
	<label commandName="NoStationaryEntity" devLabel="Invalid Stationary Reference for Unfolding." translation="固定参考无效，无法进行展开。"/>
	<label commandName="RefoldComputeError" devLabel="Failed to get Entity History." translation="无法获取实体的历史。"/>
	<label commandName="SM_BEND_GEOMETRY_ELIMINATES_PLATE" devLabel="One of the input plates would be entirely removed by the bend. Reduce the bend radius or the angle between the flanges." translation="其中一个输入板将被折弯完全删除。请减小折弯半径或凸缘之间的角度。"/>
	<label commandName="SM_COMPUTE_FLANGE_PROFILE" devLabel="Failed to compute the Flange profile." translation="未能计算凸缘轮廓。"/>
	<label commandName="SM_CORNER_CANNOT_EXTEND_BEND_DETAIL" devLabel="Cannot extend bend. Check bend radius and flange geometry." translation="无法延伸折弯。请检查折弯半径和凸缘几何图元。"/>
	<label commandName="SM_CORNER_DISCONNECTED_FACES_DETAIL" devLabel="Corner faces are not properly connected." translation="拐角面未正确连接。"/>
	<label commandName="SM_CORNER_EDGES_DONT_MEET_DETAIL" devLabel="Corner edges don't meet. Check flange angles and positions." translation="拐角边不相交。请检查凸缘角度和位置。"/>
	<label commandName="SM_CORNER_FLAT_LENGTH_ERROR_DETAIL" devLabel="Cannot calculate flat pattern length." translation="无法计算展开模式长度。"/>
	<label commandName="SM_CORNER_GENERIC_ERROR" devLabel="The calculation of the corner has failed." translation="拐角计算失败。"/>
	<label commandName="SM_CORNER_INVALID_INPUT_DETAIL" devLabel="Invalid input data for corner computation." translation="拐角计算的输入数据无效。"/>
	<label commandName="SM_CORNER_INVALID_RELIEF_GEOMETRY_DETAIL" devLabel="Corner relief geometry is invalid." translation="拐角释压几何图元无效。"/>
	<label commandName="SM_CORNER_INVALID_WIRE_DETAIL" devLabel="Corner wire geometry is invalid." translation="拐角导线几何图元无效。"/>
	<label commandName="SM_CORNER_MISSING_FACE_DETAIL" devLabel="Corner geometry is incomplete: Missing faces or edges." translation="拐角几何图元不完整: 缺少面或边。"/>
	<label commandName="SM_CORNER_MISSING_FLANGE_DETAIL" devLabel="Required flange or bend is missing." translation="缺少所需的凸缘或折弯。"/>
	<label commandName="SM_CORNER_NO_JUNCTION_DETAIL" devLabel="Junction between flanges is missing." translation="缺少凸缘之间的连接点。"/>
	<label commandName="SM_CORNER_RELATED" devLabel="The calculation of the corner has failed." translation="拐角计算失败。"/>
	<label commandName="SM_CORNER_UNSUPPORTED_SURFACE_DETAIL" devLabel="Only planar and cylindrical surfaces are supported." translation="仅支持平面和圆柱曲面。"/>
	<label commandName="SM_FLANGE_ANGLE_INVALID" devLabel="Can't create Flange because of a problem with the bend angle. Adjust parameters, then try again." translation="由于折弯角度存在问题，无法创建凸缘。请调整参数，然后重试。"/>
	<label commandName="SM_FLANGE_ANGLE_TOO_SMALL" devLabel="Can't create Flange. Bend angle is too small. Adjust parameters, then try again." translation="无法创建凸缘。折弯角度太小。请调整参数，然后重试。"/>
	<label commandName="SM_FLANGE_CFLANGE_BEND_FAILED" devLabel="One or more parameters are invalid. Try increasing flange height." translation="一个或多个参数无效。请尝试增加凸缘高度。"/>
	<label commandName="SM_FLANGE_INTERSECTION_DETECTED" devLabel="The flange is intersecting the body. Creating this flange will probably result in the body being unable to unfold or flatten." translation="凸缘与实体相交。创建此凸缘可能会导致实体无法展开或展平。"/>
	<label commandName="SM_FLANGE_INVALID_CONDITIONS" devLabel="Can't create Flange. Check the body and bend parameters, then try again." translation="无法创建凸缘。请检查实体和折弯参数，然后重试。"/>
	<label commandName="SM_GENERIC_FAILURE" devLabel="Can't complete Sheet Metal operation due to an internal error. Check the body and bend parameters, then try again." translation="由于内部错误，无法完成钣金操作。请检查实体和折弯参数，然后重试。"/>
	<label commandName="SM_MODELING_ERROR" devLabel="Can't complete Sheet Metal operation due to a model error. Check the body, then try again." translation="由于模型错误，无法完成钣金操作。请检查实体，然后重试。"/>
	<label commandName="SM_MODELING_EXCEPTION" devLabel="Can't complete Sheet Metal operation due to a model error. Check the body, then try again." translation="由于模型错误，无法完成钣金操作。请检查实体，然后重试。"/>
	<label commandName="SM_NO_VALID_EDGE" devLabel="Can't create Flange. Could not find valid edge. Check the body, then try again." translation="无法创建凸缘。找不到有效的边。请检查实体，然后重试。"/>
	<label commandName="SM_SWEEP_RELATED" devLabel="Can't complete Sheet Metal operation due to an internal error. Check the body and bend parameters, then try again." translation="由于内部错误，无法完成钣金操作。请检查实体和折弯参数，然后重试。"/>
	<label commandName="SM_TRIM_EXTEND_FAILED" devLabel="Cannot create flange because the angle is too sharp.&#xA;Adjust the Angle value to create a bend that is less extreme." translation="无法创建凸缘，因为角度太尖。&#xA;请调整“角度”值以创建不太极端的折弯。"/>
	<label commandName="SM_UNDEFINED_ERROR" devLabel="Undefined Sheet Metal Error." translation="未定义的钣金错误。"/>
	<label commandName="SM_UNFOLDER_RELATED" devLabel="Can't successfully process relief geometry. Check the body and parameters, then try again." translation="无法成功处理释压几何图元。请检查实体和参数，然后重试。"/>
	<label commandName="SM_UNFOLD_NON_MANIFOLD_EDGE" devLabel="Can't unfold. Part is not a valid Sheet Metal body. Ensure thickness is uniform. Ensure flanges do not self-intersect the body. Remove tear relief corners." translation="无法展开。零件不是有效的钣金实体。请确保厚度均匀，并确保凸缘未与实体自交。然后删除水滴形释压拐角。"/>
	<label commandName="SM_UNFOLD_RELATED1" devLabel="Can't complete Sheet Metal operation due to a model error. Check the body, then try again." translation="由于模型错误，无法完成钣金操作。请检查实体，然后重试。"/>
	<label commandName="SM_UNFOLD_RELATED2" devLabel="Can't complete Sheet Metal operation because of a problem with thickness. Adjust parameters, then try again." translation="由于厚度问题，无法完成钣金操作。请调整参数，然后重试。"/>
	<label commandName="SM_UNFOLD_RELATED3" devLabel="Can't complete Sheet Metal operation due to an internal error. Check the body and bend parameters, then try again." translation="由于内部错误，无法完成钣金操作。请检查实体和折弯参数，然后重试。"/>
	<label commandName="SM_USER_INTERRUPT" devLabel="Sheet Metal operation was interrupted before it could be completed. Try again later." translation="钣金操作在完成之前已中断。请稍后重试。"/>
	<label commandName="SM_WIDTH_EXTENTS_INVALID" devLabel="Canât generate flange or hem.&#xA;Width extents intersect or create unattached geometry. Adjust offset or distance values." translation="无法生成凸缘或折边。&#xA;宽度范围相互干涉或生成了未连接的几何图元。请调整偏移量或距离值。"/>
</Resource>