<?xml version="1.0" encoding="utf-8"?><Resource>
	<label commandName="NON_SM_ENTITIES_FOUND" devLabel="Failed to identify sheet metal faces for some edges. Ensure the body is a valid sheet metal body that keeps opposite faces separate." translation="일부 모서리의 판금 면을 식별하지 못했습니다. 본체가 반대 면을 따로 유지하는 적합한 판금 본체인지 확인하십시오."/>
	<label commandName="NoStationaryEntity" devLabel="Invalid Stationary Reference for Unfolding." translation="전개에 대한 고정 참조가 잘못되었습니다."/>
	<label commandName="RefoldComputeError" devLabel="Failed to get Entity History." translation="도면요소 사용내역을 가져오지 못했습니다."/>
	<label commandName="SM_BEND_GEOMETRY_ELIMINATES_PLATE" devLabel="One of the input plates would be entirely removed by the bend. Reduce the bend radius or the angle between the flanges." translation="입력 플레이트 중 하나가 절곡부에 의해 완전히 제거됩니다. 절곡부 반지름 또는 플랜지 사이의 각도를 줄입니다."/>
	<label commandName="SM_COMPUTE_FLANGE_PROFILE" devLabel="Failed to compute the Flange profile." translation="플랜지 프로파일을 계산하지 못했습니다."/>
	<label commandName="SM_CORNER_CANNOT_EXTEND_BEND_DETAIL" devLabel="Cannot extend bend. Check bend radius and flange geometry." translation="절곡부를 연장할 수 없습니다. 절곡부 반지름 및 플랜지 형상을 확인하십시오."/>
	<label commandName="SM_CORNER_DISCONNECTED_FACES_DETAIL" devLabel="Corner faces are not properly connected." translation="코너 면이 제대로 연결되지 않았습니다."/>
	<label commandName="SM_CORNER_EDGES_DONT_MEET_DETAIL" devLabel="Corner edges don't meet. Check flange angles and positions." translation="코너 모서리가 만나지 않습니다. 플랜지 각도와 위치를 확인합니다."/>
	<label commandName="SM_CORNER_FLAT_LENGTH_ERROR_DETAIL" devLabel="Cannot calculate flat pattern length." translation="플랫 패턴 길이를 계산할 수 없습니다."/>
	<label commandName="SM_CORNER_GENERIC_ERROR" devLabel="The calculation of the corner has failed." translation="코너를 계산하지 못했습니다."/>
	<label commandName="SM_CORNER_INVALID_INPUT_DETAIL" devLabel="Invalid input data for corner computation." translation="코너 계산을 위한 부적합한 입력 데이터."/>
	<label commandName="SM_CORNER_INVALID_RELIEF_GEOMETRY_DETAIL" devLabel="Corner relief geometry is invalid." translation="코너 릴리프 형상이 부적합합니다."/>
	<label commandName="SM_CORNER_INVALID_WIRE_DETAIL" devLabel="Corner wire geometry is invalid." translation="코너 와이어 형상이 유효하지 않습니다."/>
	<label commandName="SM_CORNER_MISSING_FACE_DETAIL" devLabel="Corner geometry is incomplete: Missing faces or edges." translation="코너 형상이 불완전합니다. 면 또는 모서리가 누락되었습니다."/>
	<label commandName="SM_CORNER_MISSING_FLANGE_DETAIL" devLabel="Required flange or bend is missing." translation="필요한 플랜지 또는 절곡부가 누락되었습니다."/>
	<label commandName="SM_CORNER_NO_JUNCTION_DETAIL" devLabel="Junction between flanges is missing." translation="플랜지 사이의 접합이 누락되었습니다."/>
	<label commandName="SM_CORNER_RELATED" devLabel="The calculation of the corner has failed." translation="코너를 계산하지 못했습니다."/>
	<label commandName="SM_CORNER_UNSUPPORTED_SURFACE_DETAIL" devLabel="Only planar and cylindrical surfaces are supported." translation="평면형 및 원통형 곡면만 지원됩니다."/>
	<label commandName="SM_FLANGE_ANGLE_INVALID" devLabel="Can't create Flange because of a problem with the bend angle. Adjust parameters, then try again." translation="절곡부 각도 문제로 인해 플랜지를 작성할 수 없습니다. 매개변수를 조정한 후, 다시 시도하십시오."/>
	<label commandName="SM_FLANGE_ANGLE_TOO_SMALL" devLabel="Can't create Flange. Bend angle is too small. Adjust parameters, then try again." translation="플랜지를 작성할 수 없습니다. 절곡부 각도가 너무 작습니다. 매개변수를 조정한 후, 다시 시도하십시오."/>
	<label commandName="SM_FLANGE_CFLANGE_BEND_FAILED" devLabel="One or more parameters are invalid. Try increasing flange height." translation="하나 이상의 매개변수가 잘못되었습니다. 플랜지 높이를 늘려보십시오."/>
	<label commandName="SM_FLANGE_INTERSECTION_DETECTED" devLabel="The flange is intersecting the body. Creating this flange will probably result in the body being unable to unfold or flatten." translation="플랜지가 본체를 교차합니다. 이 플랜지를 작성하면 본체가 전개 또는 평면화될 수 없습니다."/>
	<label commandName="SM_FLANGE_INVALID_CONDITIONS" devLabel="Can't create Flange. Check the body and bend parameters, then try again." translation="플랜지를 작성할 수 없습니다. 본체 및 절곡부 매개변수를 확인한 후 다시 시도하십시오."/>
	<label commandName="SM_GENERIC_FAILURE" devLabel="Can't complete Sheet Metal operation due to an internal error. Check the body and bend parameters, then try again." translation="내부 오류로 인해 판금 작업을 완료할 수 없습니다. 본체 및 절곡부 매개변수를 확인한 후 다시 시도하십시오."/>
	<label commandName="SM_MODELING_ERROR" devLabel="Can't complete Sheet Metal operation due to a model error. Check the body, then try again." translation="모형 오류로 인해 판금 작업을 완료할 수 없습니다. 본체를 확인한 후, 다시 시도하십시오."/>
	<label commandName="SM_MODELING_EXCEPTION" devLabel="Can't complete Sheet Metal operation due to a model error. Check the body, then try again." translation="모형 오류로 인해 판금 작업을 완료할 수 없습니다. 본체를 확인한 후, 다시 시도하십시오."/>
	<label commandName="SM_NO_VALID_EDGE" devLabel="Can't create Flange. Could not find valid edge. Check the body, then try again." translation="플랜지를 작성할 수 없습니다. 적합한 모서리를 찾을 수 없습니다. 본체를 확인한 후 다시 시도하십시오."/>
	<label commandName="SM_SWEEP_RELATED" devLabel="Can't complete Sheet Metal operation due to an internal error. Check the body and bend parameters, then try again." translation="내부 오류로 인해 판금 작업을 완료할 수 없습니다. 본체 및 절곡부 매개변수를 확인한 후 다시 시도하십시오."/>
	<label commandName="SM_TRIM_EXTEND_FAILED" devLabel="Cannot create flange because the angle is too sharp.&#xA;Adjust the Angle value to create a bend that is less extreme." translation="각도가 너무 뾰족하기 때문에 플랜지를 작성할 수 없습니다.&#xA;각도 값을 조정하여 더 작은 절곡부를 작성하십시오."/>
	<label commandName="SM_UNDEFINED_ERROR" devLabel="Undefined Sheet Metal Error." translation="정의되지 않은 판금 오류입니다."/>
	<label commandName="SM_UNFOLDER_RELATED" devLabel="Can't successfully process relief geometry. Check the body and parameters, then try again." translation="릴리프 형상을 처리할 수 없습니다. 본체 및 매개변수를 확인한 후 다시 시도하십시오."/>
	<label commandName="SM_UNFOLD_NON_MANIFOLD_EDGE" devLabel="Can't unfold. Part is not a valid Sheet Metal body. Ensure thickness is uniform. Ensure flanges do not self-intersect the body. Remove tear relief corners." translation="전개할 수 없습니다. 부품이 적합한 판금 본체가 아닙니다. 두께가 균일한지 확인하십시오. 플랜지가 본체를 자체 교차하지 않도록 하십시오. 찢어짐 릴리프 코너를 제거하십시오."/>
	<label commandName="SM_UNFOLD_RELATED1" devLabel="Can't complete Sheet Metal operation due to a model error. Check the body, then try again." translation="모형 오류로 인해 판금 작업을 완료할 수 없습니다. 본체를 확인한 후, 다시 시도하십시오."/>
	<label commandName="SM_UNFOLD_RELATED2" devLabel="Can't complete Sheet Metal operation because of a problem with thickness. Adjust parameters, then try again." translation="두께 문제로 인해 판금 작업을 완료할 수 없습니다. 매개변수를 조정한 후, 다시 시도하십시오."/>
	<label commandName="SM_UNFOLD_RELATED3" devLabel="Can't complete Sheet Metal operation due to an internal error. Check the body and bend parameters, then try again." translation="내부 오류로 인해 판금 작업을 완료할 수 없습니다. 본체 및 절곡부 매개변수를 확인한 후 다시 시도하십시오."/>
	<label commandName="SM_USER_INTERRUPT" devLabel="Sheet Metal operation was interrupted before it could be completed. Try again later." translation="판금 작업을 완료하기 전에 판금 작업이 중단되었습니다. 나중에 다시 시도하십시오."/>
	<label commandName="SM_WIDTH_EXTENTS_INVALID" devLabel="Canât generate flange or hem.&#xA;Width extents intersect or create unattached geometry. Adjust offset or distance values." translation="플랜지 또는 햄을 생성할 수 없습니다.&#xA;폭 범위가 교차하거나 부착되지 않은 형상을 작성합니다. 간격띄우기 또는 거리 값을 조정합니다."/>
</Resource>